Difference between revisions of "Troubleshooting Reinstall via LiveSuit"
Line 1: | Line 1: | ||
[[File:Duo-fel-button.jpg|450px|thumb|Location of the FEL button on the MOD Duo]] | [[File:Duo-fel-button.jpg|450px|thumb|Location of the FEL button on the MOD Duo]] | ||
+ | |||
+ | This page describes how to do a "factory reset" of the MOD Duo via LiveSuit.<br> | ||
+ | Please note that LiveSuit is not an application developed by the MOD Team | ||
Installing MOD Duo via LiveSuit | Installing MOD Duo via LiveSuit | ||
− | + | To begin: | |
− | + | # Click and hold down the FEL button on the back of the MOD Duo (in tiny hole), while you power it on. | |
− | + | # Hold it for 2 seconds, then release | |
− | + | # Connect the MOD Duo to your computer via USB cable | |
− | + | # Install the FEL mode Windows driver if not done yet (see [Installing FEL mode USB driver] section below) | |
− | + | # Run LiveSuit and deploy the MOD Duo LiveSuit image (see [Deploying LiveSuit image] below) | |
− | + | # Wait for the Duo's restore mode to activate | |
+ | # Download this file: http://download.moddevices.com/releases/modduo/reset/modduo-v1.3.2.394-reset-image.raw | ||
+ | # Copy it to the mass storage device (as usual for MOD updates) | ||
+ | # Wait until the installation finishes (he Duo will automatically reboot) | ||
== Installing FEL mode USB driver == | == Installing FEL mode USB driver == | ||
Line 82: | Line 88: | ||
− | The MOD Duo will automatically boot into restore mode after the deploy | + | The MOD Duo will automatically boot into restore mode after the deploy finishes. |
− | |||
− |
Revision as of 14:11, 23 June 2017
This page describes how to do a "factory reset" of the MOD Duo via LiveSuit.
Please note that LiveSuit is not an application developed by the MOD Team
Installing MOD Duo via LiveSuit
To begin:
- Click and hold down the FEL button on the back of the MOD Duo (in tiny hole), while you power it on.
- Hold it for 2 seconds, then release
- Connect the MOD Duo to your computer via USB cable
- Install the FEL mode Windows driver if not done yet (see [Installing FEL mode USB driver] section below)
- Run LiveSuit and deploy the MOD Duo LiveSuit image (see [Deploying LiveSuit image] below)
- Wait for the Duo's restore mode to activate
- Download this file: http://download.moddevices.com/releases/modduo/reset/modduo-v1.3.2.394-reset-image.raw
- Copy it to the mass storage device (as usual for MOD updates)
- Wait until the installation finishes (he Duo will automatically reboot)
Installing FEL mode USB driver
1. Press the windows key and 'R' at the same time to get the 'Run' dialog. Type "devmgmt.msc" and press enter. (This will open the Device Manager)
2. Find the MOD Duo device. It should appear as 'Unknown device' under 'Other devices' like the image below shows.
3. Right click on the selected item and select 'Update Driver Software...'.
4. Select 'Browse my computer for driver software'
5. Click the 'Browse' button and select the folder where you extracted the contents of the LiveSuit1.0.7.zip file, then click 'Next'.
6. Wait for Windows to finish installing the driver.
Windows might complain that it can't verify the publisher of this driver. You'll have to click to install anyway.
(This is because, as previously stated, this software was not done by the MOD Team)
7. That's it! The driver is installed. :)
8. If everything is working correctly, the Duo will appear as 'USB Device(VID_1f3a_PID_efe8)' under 'Universal Serial Bus controllers'
Deploying LiveSuit image
1. Double-click on the PhoenixSuit file to open it. The application looks like this:
2. Download...
On the LiveSuit application window, click on the Firmware tab and then the 'Image' button and select the file you just downloaded.
3. When asked about a forced format, click 'yes'.
4. Wait while the deploy takes place.
5. Deploy should complete in about 30 seconds.
The MOD Duo will automatically boot into restore mode after the deploy finishes.